Finding a Way Around the M129 250SE Engine's Oil Cooler Leak
Posted: Thu Nov 19, 2026
The M129 fuel-injected 6-cylinder engine found in the 250SE W108 and W111 cars utilises this oil cooler, which is actually a heat exchanger. Although I am unsure, it could also be in the W113 SLs and/or the early 220 car. Cracks often form around the cooler's attachment points to the left engine mount 'arm'. They should be disassembled and resolderable by a radiator repair shop. The photo up top is from eBay, where one of these things sells for around $400 for a used one.
The second one is underway. The first version of my car had a tiny leak that I ignored because it was inflated, likely due to freezing at some point while it was in Germany. Three years ago, while disassembling, rodding, and rebuilding the radiator, I figured it would be a good time to replace the cooler as well. It leaked after a few months of use, so I swapped it out for one from my extra 129 engine. Because of the unreliability of my local, old-school radiator shop's turnaround time, I've been hesitant to take my car in for repairs for at least a month or two, and I certainly don't want to shell out $400 for a used cooler that will likely leak as well.
When his began leaking, we had a quick discussion about it in the restoration thread, and I proposed connecting the oil hoses—the two big threaded fittings shown above—instead of the coolant hoses—either with a single long hose or with a pipe.
1) They're more accurately called heat exchangers than oil coolers. To make the oil heat up more quickly (oil temperature lags significantly behind coolant temperature), they inject coolant heat into the oil. Once the oil reaches a certain temperature, they either continue to inject coolant heat into the oil or inject oil heat into the coolant, depending on the driving conditions. An actual air-to-oil oil cooler was installed in the 280SE models. It sat next to the radiator and drew airflow from the grill.
Second, the amount of oil temperature that engines produce is easily handled by modern oils, rendering this unit useless. beat him to it.
In the event that yours is dripping, you can easily circumvent the cooler by purchasing 4'(122cm) of 1/2"(13mm) bulk heater hose for $10.
-On the front of the oil pan, you can see a metal coolant pipe running horizontally. From the driver's seat, it rises on the engine's left side, and a short rubber hose carries coolant to the cooler's base. Pull this hose out.
-A short hose extends from a short fitting on the engine block, which is located just behind the mechanical fuel injection pump, to the top fitting on the oil cooler (as shown in the photo above). Take off the short hose.
-Start by running the heater hose along the engine's side, inside the fuel damper. Attach it to the curved end of the horizontal pipe in front of the engine. Trim the other end as needed to create a shallow curve around the injection pump's back end. Finally, fit it to the block's fitting.
-Hint: Clamp the two short hoses in the center with your Lisle coolant hose clamp pliers; this will allow you to retain the radiator cap and drain the coolant cooler to a trickle rather than a flood. This allows you to easily refill the radiator's coolant reservoir, run the engine without the radiator cap until the temperature reaches the desired level, and observe a clear "river" of coolant without bubbles. This verifies that there are no air pockets in the cylinder head. After that, you can resume normal operations. Utilise distilled water exclusively.
The oil cooler, once mounted on the engine's side, looks like this. I have drawn the cooler's body in green and the short rubber hoses carrying coolant as red arrows.
The second one is underway. The first version of my car had a tiny leak that I ignored because it was inflated, likely due to freezing at some point while it was in Germany. Three years ago, while disassembling, rodding, and rebuilding the radiator, I figured it would be a good time to replace the cooler as well. It leaked after a few months of use, so I swapped it out for one from my extra 129 engine. Because of the unreliability of my local, old-school radiator shop's turnaround time, I've been hesitant to take my car in for repairs for at least a month or two, and I certainly don't want to shell out $400 for a used cooler that will likely leak as well.
When his began leaking, we had a quick discussion about it in the restoration thread, and I proposed connecting the oil hoses—the two big threaded fittings shown above—instead of the coolant hoses—either with a single long hose or with a pipe.
1) They're more accurately called heat exchangers than oil coolers. To make the oil heat up more quickly (oil temperature lags significantly behind coolant temperature), they inject coolant heat into the oil. Once the oil reaches a certain temperature, they either continue to inject coolant heat into the oil or inject oil heat into the coolant, depending on the driving conditions. An actual air-to-oil oil cooler was installed in the 280SE models. It sat next to the radiator and drew airflow from the grill.
Second, the amount of oil temperature that engines produce is easily handled by modern oils, rendering this unit useless. beat him to it.
In the event that yours is dripping, you can easily circumvent the cooler by purchasing 4'(122cm) of 1/2"(13mm) bulk heater hose for $10.
-On the front of the oil pan, you can see a metal coolant pipe running horizontally. From the driver's seat, it rises on the engine's left side, and a short rubber hose carries coolant to the cooler's base. Pull this hose out.
-A short hose extends from a short fitting on the engine block, which is located just behind the mechanical fuel injection pump, to the top fitting on the oil cooler (as shown in the photo above). Take off the short hose.
-Start by running the heater hose along the engine's side, inside the fuel damper. Attach it to the curved end of the horizontal pipe in front of the engine. Trim the other end as needed to create a shallow curve around the injection pump's back end. Finally, fit it to the block's fitting.
-Hint: Clamp the two short hoses in the center with your Lisle coolant hose clamp pliers; this will allow you to retain the radiator cap and drain the coolant cooler to a trickle rather than a flood. This allows you to easily refill the radiator's coolant reservoir, run the engine without the radiator cap until the temperature reaches the desired level, and observe a clear "river" of coolant without bubbles. This verifies that there are no air pockets in the cylinder head. After that, you can resume normal operations. Utilise distilled water exclusively.
The oil cooler, once mounted on the engine's side, looks like this. I have drawn the cooler's body in green and the short rubber hoses carrying coolant as red arrows.